관리-도구

편집 파일: brcmfmac.h

/* * Copyright (c) 2016 Broadcom Corporation * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ #ifndef _LINUX_BRCMFMAC_PLATFORM_H #define _LINUX_BRCMFMAC_PLATFORM_H #define BRCMFMAC_PDATA_NAME "brcmfmac" #define BRCMFMAC_COUNTRY_BUF_SZ 4 /* * Platform specific driver functions and data. Through the platform specific * device data functions and data can be provided to help the brcmfmac driver to * operate with the device in combination with the used platform. */ /** * Note: the brcmfmac can be loaded as module or be statically built-in into * the kernel. If built-in then do note that it uses module_init (and * module_exit) routines which equal device_initcall. So if you intend to * create a module with the platform specific data for the brcmfmac and have * it built-in to the kernel then use a higher initcall then device_initcall * (see init.h). If this is not done then brcmfmac will load without problems * but will not pickup the platform data. * * When the driver does not "detect" platform driver data then it will continue * without reporting anything and just assume there is no data needed. Which is * probably true for most platforms. */ /** * enum brcmf_bus_type - Bus type identifier. Currently SDIO, USB and PCIE are * supported. */ enum brcmf_bus_type { BRCMF_BUSTYPE_SDIO, BRCMF_BUSTYPE_USB, BRCMF_BUSTYPE_PCIE }; /** * struct brcmfmac_sdio_pd - SDIO Device specific platform data. * * @txglomsz: SDIO txglom size. Use 0 if default of driver is to be * used. * @drive_strength: is the preferred drive_strength to be used for the SDIO * pins. If 0 then a default value will be used. This is * the target drive strength, the exact drive strength * which will be used depends on the capabilities of the * device. * @oob_irq_supported: does the board have support for OOB interrupts. SDIO * in-band interrupts are relatively slow and for having * less overhead on interrupt processing an out of band * interrupt can be used. If the HW supports this then * enable this by setting this field to true and configure * the oob related fields. * @oob_irq_nr, * @oob_irq_flags: the OOB interrupt information. The values are used for * registering the irq using request_irq function. * @broken_sg_support: flag for broken sg list support of SDIO host controller. * Set this to true if the SDIO host controller has higher * align requirement than 32 bytes for each scatterlist * item. * @sd_head_align: alignment requirement for start of data buffer. * @sd_sgentry_align: length alignment requirement for each sg entry. * @reset: This function can get called if the device communication * broke down. This functionality is particularly useful in * case of SDIO type devices. It is possible to reset a * dongle via sdio data interface, but it requires that * this is fully functional. This function is chip/module * specific and this function should return only after the * complete reset has completed. */ struct brcmfmac_sdio_pd { int txglomsz; unsigned int drive_strength; bool oob_irq_supported; unsigned int oob_irq_nr; unsigned long oob_irq_flags; bool broken_sg_support; unsigned short sd_head_align; unsigned short sd_sgentry_align; void (*reset)(void); }; /** * struct brcmfmac_pd_cc_entry - Struct for translating user space country code * (iso3166) to firmware country code and * revision. * * @iso3166: iso3166 alpha 2 country code string. * @cc: firmware country code string. * @rev: firmware country code revision. */ struct brcmfmac_pd_cc_entry { char iso3166[BRCMFMAC_COUNTRY_BUF_SZ]; char cc[BRCMFMAC_COUNTRY_BUF_SZ]; s32 rev; }; /** * struct brcmfmac_pd_cc - Struct for translating country codes as set by user * space to a country code and rev which can be used by * firmware. * * @table_size: number of entries in table (> 0) * @table: array of 1 or more elements with translation information. */ struct brcmfmac_pd_cc { int table_size; struct brcmfmac_pd_cc_entry table[]; }; /** * struct brcmfmac_pd_device - Device specific platform data. (id/rev/bus_type) * is the unique identifier of the device. * * @id: ID of the device for which this data is. In case of SDIO * or PCIE this is the chipid as identified by chip.c In * case of USB this is the chipid as identified by the * device query. * @rev: chip revision, see id. * @bus_type: The type of bus. Some chipid/rev exist for different bus * types. Each bus type has its own set of settings. * @feature_disable: Bitmask of features to disable (override), See feature.c * in brcmfmac for details. * @country_codes: If available, pointer to struct for translating country * codes. * @bus: Bus specific (union) device settings. Currently only * SDIO. */ struct brcmfmac_pd_device { unsigned int id; unsigned int rev; enum brcmf_bus_type bus_type; unsigned int feature_disable; struct brcmfmac_pd_cc *country_codes; union { struct brcmfmac_sdio_pd sdio; } bus; }; /** * struct brcmfmac_platform_data - BRCMFMAC specific platform data. * * @power_on: This function is called by the brcmfmac driver when the module * gets loaded. This can be particularly useful for low power * devices. The platform spcific routine may for example decide to * power up the complete device. If there is no use-case for this * function then provide NULL. * @power_off: This function is called by the brcmfmac when the module gets * unloaded. At this point the devices can be powered down or * otherwise be reset. So if an actual power_off is not supported * but reset is supported by the devices then reset the devices * when this function gets called. This can be particularly useful * for low power devices. If there is no use-case for this * function then provide NULL. */ struct brcmfmac_platform_data { void (*power_on)(void); void (*power_off)(void); char *fw_alternative_path; int device_count; struct brcmfmac_pd_device devices[]; }; #endif /* _LINUX_BRCMFMAC_PLATFORM_H */