관리-도구

편집 파일: omap1-usb.h

/* SPDX-License-Identifier: GPL-2.0 */ #ifndef __SOC_TI_OMAP1_USB #define __SOC_TI_OMAP1_USB /* * Constants in this file are used all over the place, in platform * code, as well as the udc, phy and ohci drivers. * This is not a great design, but unlikely to get fixed after * such a long time. Don't do this elsewhere. */ #define OMAP1_OTG_BASE 0xfffb0400 #define OMAP1_UDC_BASE 0xfffb4000 #define OMAP2_UDC_BASE 0x4805e200 #define OMAP2_OTG_BASE 0x4805e300 #define OTG_BASE OMAP1_OTG_BASE #define UDC_BASE OMAP1_UDC_BASE /* * OTG and transceiver registers, for OMAPs starting with ARM926 */ #define OTG_REV (OTG_BASE + 0x00) #define OTG_SYSCON_1 (OTG_BASE + 0x04) # define USB2_TRX_MODE(w) (((w)>>24)&0x07) # define USB1_TRX_MODE(w) (((w)>>20)&0x07) # define USB0_TRX_MODE(w) (((w)>>16)&0x07) # define OTG_IDLE_EN (1 << 15) # define HST_IDLE_EN (1 << 14) # define DEV_IDLE_EN (1 << 13) # define OTG_RESET_DONE (1 << 2) # define OTG_SOFT_RESET (1 << 1) #define OTG_SYSCON_2 (OTG_BASE + 0x08) # define OTG_EN (1 << 31) # define USBX_SYNCHRO (1 << 30) # define OTG_MST16 (1 << 29) # define SRP_GPDATA (1 << 28) # define SRP_GPDVBUS (1 << 27) # define SRP_GPUVBUS(w) (((w)>>24)&0x07) # define A_WAIT_VRISE(w) (((w)>>20)&0x07) # define B_ASE_BRST(w) (((w)>>16)&0x07) # define SRP_DPW (1 << 14) # define SRP_DATA (1 << 13) # define SRP_VBUS (1 << 12) # define OTG_PADEN (1 << 10) # define HMC_PADEN (1 << 9) # define UHOST_EN (1 << 8) # define HMC_TLLSPEED (1 << 7) # define HMC_TLLATTACH (1 << 6) # define OTG_HMC(w) (((w)>>0)&0x3f) #define OTG_CTRL (OTG_BASE + 0x0c) # define OTG_USB2_EN (1 << 29) # define OTG_USB2_DP (1 << 28) # define OTG_USB2_DM (1 << 27) # define OTG_USB1_EN (1 << 26) # define OTG_USB1_DP (1 << 25) # define OTG_USB1_DM (1 << 24) # define OTG_USB0_EN (1 << 23) # define OTG_USB0_DP (1 << 22) # define OTG_USB0_DM (1 << 21) # define OTG_ASESSVLD (1 << 20) # define OTG_BSESSEND (1 << 19) # define OTG_BSESSVLD (1 << 18) # define OTG_VBUSVLD (1 << 17) # define OTG_ID (1 << 16) # define OTG_DRIVER_SEL (1 << 15) # define OTG_A_SETB_HNPEN (1 << 12) # define OTG_A_BUSREQ (1 << 11) # define OTG_B_HNPEN (1 << 9) # define OTG_B_BUSREQ (1 << 8) # define OTG_BUSDROP (1 << 7) # define OTG_PULLDOWN (1 << 5) # define OTG_PULLUP (1 << 4) # define OTG_DRV_VBUS (1 << 3) # define OTG_PD_VBUS (1 << 2) # define OTG_PU_VBUS (1 << 1) # define OTG_PU_ID (1 << 0) #define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */ # define DRIVER_SWITCH (1 << 15) # define A_VBUS_ERR (1 << 13) # define A_REQ_TMROUT (1 << 12) # define A_SRP_DETECT (1 << 11) # define B_HNP_FAIL (1 << 10) # define B_SRP_TMROUT (1 << 9) # define B_SRP_DONE (1 << 8) # define B_SRP_STARTED (1 << 7) # define OPRT_CHG (1 << 0) #define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */ // same bits as in IRQ_EN #define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */ # define OTGVPD (1 << 14) # define OTGVPU (1 << 13) # define OTGPUID (1 << 12) # define USB2VDR (1 << 10) # define USB2PDEN (1 << 9) # define USB2PUEN (1 << 8) # define USB1VDR (1 << 6) # define USB1PDEN (1 << 5) # define USB1PUEN (1 << 4) # define USB0VDR (1 << 2) # define USB0PDEN (1 << 1) # define USB0PUEN (1 << 0) #define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */ #define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */ /*-------------------------------------------------------------------------*/ /* OMAP1 */ #define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064) # define CONF_USB2_UNI_R (1 << 8) # define CONF_USB1_UNI_R (1 << 7) # define CONF_USB_PORT0_R(x) (((x)>>4)&0x7) # define CONF_USB0_ISOLATE_R (1 << 3) # define CONF_USB_PWRDN_DM_R (1 << 2) # define CONF_USB_PWRDN_DP_R (1 << 1) #endif